Smart PCB PCBA FPC ComponentsPCB/PCBA/FPC/Clone boards/membrane switch/Modules/Sensors/NTC/Aluminum heatsink/components

Your Current Position: Products

RS422 to TTL/UART/MCU Serial Port Signal Mutual Module with Over-Voltage Over-Current Protection-3.3V

VCC: + 3.3V

TXD : The module's TTL (UART) to send, connected to the microcontroller's RXD receiver pin;

RXD : The module's TTL (UART) receiver, connected to the microcontroller TXD send pin;

GND : The module ground wire (this wire must be connected with the ground wire of microcontroller system);
XL 6009 DC to DC Step Up Converter xl6009 step-up power module dc motor

This DC-DC Module is based on IC XL6009E1 which is a high-performance step-up switching current (BOOST) module. The module uses the second generation of high-frequency switching technology XL6009E1 core chip that offers superior performance over the first generation technology LM2577. XL6009 replaces LM2577 module as LM2577 is about to be phased out.
SIM900A module, development board, GSM/GPRS/STM32 \ super TC35i wireless data transmission module

Product Description:

ardu 51 STM32 AVR MCU compatible
Prototype expand
The dual frequency 900/ 1800 MHz, GPRS multi-slot class 10/8,GPRS mobile station class B
Power supply range: voltage is 4.6-5.2v; current is 1A or more(the current is very important).
Low power consume: 1.5mA (sleep mode)
Operating temperature range: -40 degrees C to +85 C
Communication interface: The TTL level serial interface compatible 2.85 3.3 5v MCU
Size:49*50mm
Wedding special igniter 12V DC universal high voltage generator pulse high voltage module output 60KV arc
MAX485 Module RS-485 TTL to RS485 MAX485CSA Converter Module

1 on-board MAX485 chip , is a tool for RS-485 communications , low-power , Slew-Rate Transceiver
2 onboard then 5.08 (mm) pitch 2P terminal for easy wiring RS-485 communication
3 the chip has drawn all of the pins can be controlled by the microcontroller operation
4 Working voltage : 5V
5 board size : 44 (mm) x14 (mm)
1000W ZVS Carbon Steel Flyback Driver Low Voltage Stable Induction Heating Board Module Plate

100% brand new and high quality!
This section of induction heating using low-voltage DC power supply 12-48V.
Maximum current 20A, maximum power 1000W.
Can be used for DIY players to heat treatment of small parts such as quenching, annealing, etc.
Can directly heat iron, carbon steel, graphite, titanium alloy and other materials.
Also can be used with a graphite crucible melting gold, silver, copper, aluminum and other metals, uniform heating fast, very convenient.
Smart Electronics DC DC Boost Converter Constant Module Current Mobile Power Supply 250W 10A LED Driver Module Non-isolated Step Up Module

DC DC Boost Converter Constant Module Current Mobile Power Supply 250W 10A LED Driver Module Non-isolated Step Up Module

Applications:

1, DIY a power supply, 12V can input and output can 12-50V adjustable.

2, the power supply for your electronic device, according to your
system can set the output voltage value.

3, as the car power supply for your laptop, PDA or a variety of digital
products supply.

4, DIY a mobile notebook power supply: 12V coupled with high-capacity
lithium battery pack, so you can go where light where books.

5, solar panel regulator.
Smart Electronics AC-DC Power Supply Module AC 100-240V to DC 24V 9A Switching Power Supply Board

AC-DC Power Supply Module AC 100-240V to DC 24V 9A Switching Power Supply Board

Product Description:
Input voltage: AC 100-240V 50/60HZ
Output Voltage: DC 24V
Output Current: 6-9A
Output Power: 150W ( Max 220W )
Location Pore Size: 105.8 x 55.7mm
Overall Dimensions: 115 x 65mm
Ripple Noise: Less than 150MV
Overcurrent protection: Yes
Overload Protection: Yes
Short circuit protection: Yes
Smart Electronics 100W 2SC5200+2SA1943 Audio Amplifier Board Mono Channel HIFI Power Amplifier Board Dual DC35V

100W 2SC5200+2SA1943 Audio Amplifier Board Mono Channel HIFI Power Amplifier Board Dual DC35V

Operating voltage: Dual DC 10 - 45V recommended Dual DC 35V
Rated output power :100W(4 Ohm ± 35V)
Maximum output power : 150W (4 Ohm ± 45V) enormous heat, is not recommended
PCB size :30 x 50 x 35mm
Pitch : 5.08mm
Hole distance between two power tube : 47mm
Smart Electronics Wireless Charger 10W 7.5W PCBA Circuit Board Coil Module DIY Charger

Wireless Charger 10W 7.5W PCBA Circuit Board Coil Module DIY Charger

The input voltage: 5V2A output : 5V1A

The input voltage: 5V4A 9V1.67A(qc3.0)

Output : 5V2A 9V1A

Charging current: 1000mAh

Charging power: up to 10W

Wireless conversion efficiency: 73%, boost circuit 90%
Smart Electronics 3D printer parts DIY motherboard kit mega2560 + LCD circuit control board

3D printer parts DIY motherboard kit mega2560 + LCD circuit control board

The diode D1 supplied by the ramps to the mega board is not welded, that is to say, the mega2560
board needs to be separately powered by usb5v or through the power connector (it is not recommended
to power more than 12V officially). Please understand. If you want to use LCD offline printing, you need to
power the ramps 1.4 yourself, otherwise you can't use it.
Smart Electronics Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Product Parameters
1. Input power supply: 5V 2A or 9V 1.67-2a, output: 5V 1A or 9V 1.2A
2. Product weight: 0.035kg
3. Charging power: 5W / 7.5w/10w automatic identification
4. Transmission distance: 2-8mm
5. Executive standard: Qi wireless charging standard
6. Product certification: CE / FCC / RoHS

First <Previous ... 9 10 11 12 13 14 15 16 17 ... Next> End

SHENZHEN SMART ELECTRONICS CO.,LTD.

Address :

No.403 , Shangshuijing Complex Bldg, Jihua Rd, Longgang District, Shenzhen

Email : info@smart-bes.com

PH/Fax : 86-755-83877216

Skype : smartbes

Payment Methods

——

Bank Transfer

Paypal

WeChat

Alipay

Visa

Shippment Options

——

DHL

FeedEx

TNT

UPS

EMS

Quick Links

——

Request a Quote

Copyright © 2024 Shenzhen Smart Electronics Co., Ltd all rights reserved

TOP

86-755-83877216

smartbes

smartbes

info@smart-bes.com