Search

Smart Electronics Golden SW-520D Angle Sensor Module Ball Switch Vibration Switch Tilt Sensor Module

Products > Module > Smart Electronics Golden SW-520D Angle Sensor Module Ball Switch Vibration Switch Tilt Sensor Module
    • 1

Smart Electronics Golden SW-520D Angle Sensor Module Ball Switch Vibration Switch Tilt Sensor Module

Module features:
1. Using high sensitivity angle switch SW-520D as the sensor
2. Comparator output, clean signal, good waveform, strong driving ability, exceeding 15mA.
3. Working voltage 3.3V-5V
4. Output form: Digital switch output (0 and 1)
5. Equipped with fixed bolt holes for easy installation
6. Small PCB size: 3.2cm x 1.4cm
7. Using a wide voltage LM393 comparator
shared：

Smart Electronics Golden SW-520D Angle Sensor Module Ball

Switch Vibration Switch Tilt Sensor Module

Module features: 1. Using high sensitivity angle switch SW-520D as the sensor 2. Comparator output, clean signal, good waveform, strong driving ability, exceeding 15mA. 3. Working voltage 3.3V-5V 4. Output form: Digital switch output (0 and 1) 5. Equipped with fixed bolt holes for easy installation 6. Small PCB size: 3.2cm x 1.4cm 7. Using a wide voltage LM393 comparator




Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

XL4016 DC/CC Adjustable 0.2- 9A 300w Step Down Buck Converter 5-40V To 1.2-35V Power Supply Module LED Driver

Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Detailed Images

Universal Wireless Charging PCBA Coil Charging Pcb Circuit Board Qi Wireless charger receiver module

FM Transmitter Wireless Microphone Surveillance Frequency Board Module For Arduino Adjustable Capacitor DC 800M 85-115MHz

2x6W DC 5V 3.7V speaker modified Stereo Bluetooth amplifier board can connected lithium battery with charge management A8-020

100% Brand New Size: 7x4x0.7cm Conversion:1cm=0.39inch /1 inch =2.54cm

DC5V-12V Charging module for lithium battery 18650 UPS voltage converter uninterruptible power supply module

Product parameters: Starting voltage: 1.2V Working voltage: 2V-6.5V Output voltage: 5V/9V/12V optional Working voltage is 2V-6.5V Input current: 2A Output power: ≤8W (no matter how high it is, it is easy to overheat) No-load current 2-3.5mA (input 1.5V output 12V) Board size: 33*16*6.5mm Output pad: USB/DC optional

LNA 50-4000 MHz RF SPF5189 NF 0.6dB Low Noise Amplifier Signal Receiver Board Wireless Communication Module With Shield Shell

Specifications: LNA: 50-4000mhz NF: SPF5189Z LNA0: 0.6 dB Amplifier: FM Size: 34 x 25mm/1.33 x1.0inch

TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

BH1750FVI digital Light Intensity BH1750 Light Module Light Ball DC5V

Keyes BH1750FVI Digital Light Sensor Module is a kind of integrated circuit of digital light intensity sensor for two-wire serial bus interface. Using the light intensity data collected by the module, the brightness of the LCD and keyboard background lamps can be adjusted. Module resolution can detect wide range of light intensity changes.

DC DC Boost Converter Constant Module Current Mobile Power Supply 250W 10A LED Driver Module Non-isolated Step Up Module

Applications: 1, DIY a power supply, 12V can input and output can 12-50V adjustable. 2, the power supply for your electronic device, according to your system can set the output voltage value. 3, as the car power supply for your laptop, PDA or a variety of digital products supply. 4, DIY a mobile notebook power supply: 12V coupled with high-capacity lithium battery pack, so you can go where light where books. 5, solar panel regulator.

100W 2SC5200+2SA1943 Audio Amplifier Board Mono Channel HIFI Power Amplifier Board Dual DC35V

Operating voltage: Dual DC 10 - 45V recommended Dual DC 35V Rated output power :100W(4 Ohm ± 35V) Maximum output power : 150W (4 Ohm ± 45V) enormous heat, is not recommended PCB size :30 x 50 x 35mm Pitch : 5.08mm Hole distance between two power tube : 47mm

ACS712ELC-05B 5A range ACS712 module AC current sensor module

1. Current sensor chip: ACS712ELC-05B; 2. Pin 5V power supply, onboard power indicator; 3. The module can measure plus or minus 5A current, corresponding to the analog output 185mV/A; 4. When no detection current passes, the output voltage is VCC/2; 5. PCB board size: 31(mm)x13(mm);

HC-SR501 Adjust IR Pyroelectric Infrared PIR Motion Sensor Detector Module

Automatic induction: When someone enters its induction range, enter the high level, people leave the sensor range is automatically delayed off high. Output low. 2. photosensitive control (optional): the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.

New Arrival Raspberry Pi 3 Model B+ Wide Angle Camera 5MP Adjustable-focus Mini Vision Video Camera module

Temperature (Operation): -20°C to 70°C Temperature (Stable Image) : 0°C to 50°C Focus :Fixed Object distance:30CM-∞ Resolution: 800LW/PH (Center) Working power supply : 3.3v(pin15) Operating system: for Raspberry Pi Certifications :FCC and CE Sensor Type: OV5647 (1/4” ) Active Array Size : 2592*1944 Sensitivity: 600mV/Lux-sec F/No: 2.35 EFL: 1.55 mm BFL(Optical): 3.1mm FOV: 160° TV Distortion :<14.5% Relative Illumination (Sensor) : 70% IR Filter : 650±10nm

Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Product Parameters 1. Input power supply: 5V 2A or 9V 1.67-2a, output: 5V 1A or 9V 1.2A 2. Product weight: 0.035kg 3. Charging power: 5W / 7.5w/10w automatic identification 4. Transmission distance: 2-8mm 5. Executive standard: Qi wireless charging standard 6. Product certification: CE / FCC / RoHS

HW-658 USB Port GPS Module For Raspberry Pi

Suitable For Raspberry Pi A B A+ B+ Zero 2 3. Connect via 1*8 2.54 separation distance pin header or USB micro data cable. Adopting L80-39 mould project, with 15 x 15 x 4mm Patch aerial. Super low power consumption, quick location. Support Short-circuit Protection and Aerial Detection. Support self-auxiliary AGPS (EASY technology), no need of external memory. Support LOCUS, DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN).

Thermoelectric Peltier Refrigeration Cooling System Kit Cooler for DIY TEC-12706 mini air conditioner

Semiconductor coolers are a form of solid state cooling that incorporates both semiconductor ​Technologies and electronic assembly techniques. Here is the Kit you can made cooling system for yourself easy and fun Enjoy the DIY

HD SPI 0.96 inch 1.3 inch 1.44 inch 1.8" tft spi st7735 80 x 160 color display OLED LCD screen st7735

GY-291 ADXL345 Digital Three 3 Triple Axis Sensor Acceleration Module IIC SPI Replace ADXL335

1. Adxl345 digital three-axis acceleration of gravity tilt module Ar code iic / spi. 2. Name: the adxl345 module (three-axis acceleration of gravity). 3. use the chip: the adxl345. 4. power supply :3-5v. 5. means of communication: the iic / spi communication protocol. 6. measuring range: ± 2g ± 16g. 7. schematics, manuals and reference documentation of relevant data. 8. 51, the avr, the Ar microcontroller test code. 9. 3-axis, ± 2g / ± 4g / ± 8g / ± 16g.

DIY Ble 5.0 Audio Receiver Module MP3 Ble Decoder Board Car Audio Speaker 4.1

HC-05 master-slave integrated BlE module DIY wireless serial port transparent electronic module BLE
Previous： Smart Electronics black mini version RC-522 RC522 RFID Wireless IC Module S50 Fudan SPI Writer Reader Card Key Chain Sensor Kits
Next： Smart Electronics MFRC-522 RC522 RFID Module Red Board (with accessories) IC Card Proximity Module
Return
TOP
86-755-83877216
smartbes
smartbes