Search

Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

Products > Module > Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6

Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection
shared：

Model Number
18650 tp4056
Product Name
Lithium Battery Charger Module
Maximum charging current
1000mA
Input voltage
5V
Charging cut-off voltage
4.2V ± 1%
Three interfaces
MICRO/MINI/TYPE-C
Over discharge protection voltage
2.5V
Overcurrent protection current
3A

Type 1
1A lithium battery protection MICRO interface
Type 2
TP4056 without protective MINI interface
Type 3
TP4056 without protected MICRO interface
Type 4
TP4056 with protected TYPE-C interface
Type 5
TP4056 lithium battery without protection TYPE-C

Usage:

Attention: When the battery is first connected, there may be no voltage output between OUT+and OUT -.

At this time, charging with 5V voltage can activate the protection circuit. If the battery is short circuited from B+B -

and then connected again, charging is also necessary to activate the protection circuit. When using a mobile

phone charger for input, it should be noted that the charger must be able to output 1A or above,

otherwise it may not charge properly.


The TYPE C USB base and its adjacent+- pad are the power input terminals, connected to a 5V voltage.

B+is connected to the positive pole of the lithium battery, and B - is connected to the negative pole of the

lithium battery. OUT+and OUT - connect to the load, such as the positive and negative poles of the mobile

booster board or other loads.


Connect the battery to B+B -, insert the phone charger into the USB base, the red light indicates charging,

and the blue light indicates full charge.


Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

Smart Electronics 0.49 inch OLED LCD screen 64*32 dot matrix SSD1306 driver 14Pin IIC interface

0.49 inch OLED LCD screen 64*32 dot matrix SSD1306 driver 14Pin IIC interface Feature Size: 0.49 inch Dot matrix: 64*32 Monochrome: white, blue Hardware interface: I2C (14 feet) Driver chip: SSD1306/SH1106 Drive voltage: 3.3V Working temperature: -40℃-+70℃; Storage temperature: -40℃-+85℃; Product features: self-luminous, high brightness, high contrast, ultra-thin, full viewing angle, visible under sunlight, wide temperature, low power consumption, fast response speed

Smart Electronics AC-DC Power Supply Module AC 100-240V to DC 24V 9A Switching Power Supply Board

AC-DC Power Supply Module AC 100-240V to DC 24V 9A Switching Power Supply Board Product Description: Input voltage: AC 100-240V 50/60HZ Output Voltage: DC 24V Output Current: 6-9A Output Power: 150W ( Max 220W ) Location Pore Size: 105.8 x 55.7mm Overall Dimensions: 115 x 65mm Ripple Noise: Less than 150MV Overcurrent protection: Yes Overload Protection: Yes Short circuit protection: Yes

Smart Electronics LCD1602 yellow-green screen 1602A lcd display blue

LCD1602 yellow-green screen 1602A lcd display blue 69.5*21.8*17.8 weighs about 30 grams

Smart Electronics High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2

High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2 Item: XH-M190 Name: Digital Audio Amplifier Model: XH-M190 The number of chips: dual-core chips Chip Name: TPA3116D2 Input power: DC12V-24V Output power: 100Wx2 Input Impedance: 51Kx2 Power efficiency:> 90% Output resistance: 4-8Ohm Frequency range: 14-100KHz Noise ratio: 100db Output channel: left and right dual channel Size: 105 * 65 * 23MM Net weight: 90g

Smart Electronics TTGO T-Display ESP32 WiFi And Ble Module Development Board

TTGO T-Display ESP32 WiFi And Ble Module Development Board Chipset： ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH： QSPI flash 4MB SRAM： 520 kB SRAM Button： Reset USB to TTL： CP2104 Modular interface： UART,SPI,SDIO,I2C,LED PWM,TV PWM,I2S,IRGPIO,ADC,capacitor touch sensor,DACLNA pre-amplifier

Smart Electronics 3.5 inch SPI serial port TFT LCD display module LCD touch screen ILI9488/6/1 driver 320X480

3.5 inch SPI serial port TFT LCD display module LCD touch screen ILI9488/6/1 driver 320X480

Smart Electronics JDY-16 Ble 4.2 module high-speed transparent BLE support airsync iBeacon super CC2541

JDY-16 Ble 4.2 module high-speed transparent BLE support airsync iBeacon super CC2541 Feature No byte limit for serial port transmission and reception during transparent transmission Effective communication distance within 80 meters Working temperature: -40~+80 ℃ Communication rate 8k Bytes per second Support UART and IIC communication methods Working voltage: 1.8-3.3V

Smart Electronics New Original SIMCOM SIM7000A SIM7000G SIM7000E, NB/CAT-M/GSM Module

New Original SIMCOM SIM7000A SIM7000G SIM7000E, NB/CAT-M/GSM Module

Smart Electronics HC-08 BLE4.0 master-slave integrated Bluetooth module CC2540 wireless serial communication data transmission module

HC-08 BLE4.0 master-slave integrated Bluetooth module CC2540 wireless serial communication data transmission module Product model: HC-08 Working frequency band: 2.4G Communication interface: UART3.3VTL level Working voltage: 3.0-3.6V RSSI support: not supported Communication level: 3.3V Transmission power: 4dBm Reference distance: 80 meters Air speed: 2Mbps Antenna interface: built-in PCB antenna Communication current: 0.4uA Receiving sensitivity: 85dbm@2Mbps Working humidity: 10%~90% Storage temperature: 40 ℃ -+80 ℃ Working temperature: -25 ℃ -75 ℃

BH1750FVI digital Light Intensity BH1750 Light Module Light Ball DC5V

Keyes BH1750FVI Digital Light Sensor Module is a kind of integrated circuit of digital light intensity sensor for two-wire serial bus interface. Using the light intensity data collected by the module, the brightness of the LCD and keyboard background lamps can be adjusted. Module resolution can detect wide range of light intensity changes.

Smart Electronics Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board

Electric Unit PAM8610 12V 2x15W Dual Channel Stereo C Digital power amplifier board This plate with switching function, SW short, will turn off the power amplifier Working Mode: Class D (PWM modulation type) Chip Type: PAM8610 Power Range: DC 6V-15V (self-protection) Recommended Voltage: DC 12V(2A) Output Power: 10Wx2(8Ω) 15Wx2(4Ω) Frequency Response: 20HZ-15KHZ Static Current: 20MA (DC12V) SNR: 90% Recommended Speakers: 10-100W Input Impedance: 15K Output Impedance: 4-8Ω Harmonic Distortion: <0.1% Size: Approx. 3cm x 2.5cm/ 1.19" x 0.98"

Smart Electronics 4 channel 5V 12V 24V relay module with optocoupler low level trigger development board module

4 channel 5V 12V 24V relay module with optocoupler low level trigger development board module 5 V-12V to TTL control signal The control signal DC or AC, 220V AC load can be controlled. There is a normally open and one normally closed contact A power indicator light A control indicator, pull off, disconnect does not shine Transistor drive to increase the relay coil control pins high impedance. The control pin has a pull-down circuit to prevent malfunction relay vacant.

Smart Electronics GY-530 VL53L0X Laser Ranging Sensor ToF Ranging Time of Flight Ranging Sensor Module

GY-530 VL53L0X Laser Ranging Sensor ToF Ranging Time of Flight Ranging Sensor Module

Smart Electronics Data transmission/transceiver/SI4432 industrial grade Wireless RF receiver cc1101 module

Data transmission transceiver SI4432 industrial grade Wireless RF receiver cc1101 module

Smart Electronics IR Infrared Proximity Sensor Obstacle Avoidance module for Arduino Raspberry Pi DIY Smart Car 3PIN Robot Reflective Photoelec

IR Infrared Proximity Sensor Obstacle Avoidance module for Arduino Raspberry Pi DIY Smart Car 3PIN Robot Reflective Photoelec

Wedding special igniter 12V DC universal high voltage generator pulse high voltage module output 60KV arc

Smart Electronics IRS2092S 500W Mono Channel Digital Amplifier Class D HIFI Power Amp Board 20Hz-20KHz Digital Amplifier Module

IRS2092S 500W Mono Channel Digital Amplifier Class D HIFI Power Amp Board 20Hz-20KHz Digital Amplifier Module

USB Power Bank Charger Circuit Board Step Up Boost Power Module + 5S 18650 Li-ion Case Shell DIY Kit Powerbank

1.Aplly Battery Type:18650 battery(not include) 2.Output Voltage: 5V 2.1A 3.Input Voltage: 5V1A 4.Instructions: Level 4 Capacity indicator 5.Lighting: with LED lights 6.Size: 140 * 64 * 22mm 7.Rated Voltage : 3.7V ( Suit for 3.2V-4.2V. The batteries are in parallel)

500W Mono Channel Digital Amplifier Class D HIFI Power Amp Board 20Hz-20KHz Digital Amplifier Module

Use precautions: 1. Rated supply voltage is ±65V, ±58---±70V range, do not over 70V! positive and ​negative do not pick wrong 2. Recommended power supply ±65V 3. Recommended 4-8Ω / 10-18inch speaker 4. Carefully check before electricity, ensure the wiring is correct.

Smart Electronics HC-SR312 Human body sensing infrared sensor PIR infrared module HC-SR312

HC-SR312 Human body sensing infrared sensor PIR infrared module HC-SR312
Previous： Smart Eletronics Universal Wireless Charging PCBA Coil Charging Pcb Circuit Board Qi Wireless charger receiver module
Next： Smart Electronics HC-05 master-slave integrated BlE module DIY wireless serial port transparent electronic module BLE
Return
TOP
86-755-83877216
smartbes
smartbes